Kirby vacuum pre-owned shampooer

Home >

Alternative Views:

Product Code: K-ACC-SMPUSED

Out of Stock

Description

OUT of STOCK

USED KIRBY VACUUM NOZZLE BODY ONLY
USED and DIRTY but FUNCTIONAL

In order to offer you the lowest price possible we will ship the accessory to you without cleaning it first. We will make sure that it is fully functional but you will have to do the cleaning yourself.
Due to the fact that parts of the shampooer may come from different models the system you will get may have DIFFERENT COLORED components.

SYSTEM:
Will work with ANY of following models:
Generation 3 (G3)
Generation 4 (G4)
Generation 5 (G5)
Generation 6 (G6)
Ultimate G (G7 or UG)
Ultimate G Diamond Ed.(G7 or DE)
Sentria (G10)
At the time of creating this listing Sentria is the current Kirby vacuum model. If there is a new model out there today - contact us for compatibility.

INCLUDED:

Tray with shield
Nozzle
Brush roll
Belt
Container with cap
Hose

NO SHAMPOO included. If you need shampoo - buy it HERE

CLEANUP INSTRUCTIONS: (if you choose to clean it that it):
Use dishwasher soap to remove dirt and rubbing alcohol (available at your local pharmacy) to remove paint if any.
Leave the water tank open and let it dry. If you choose to wipe it off inside - do NOT use toilet tissue as it will disintegrate and eventually clog the valve under ON/OFF knob.
It is better to avoid submerging brush roll in the water. If you did - leave it standing vertically so water would drain.

MANUAL - If you have never used this shampooed we highly recommend taking a look at our ONLINE CARPET SHAMPOO SYSTEM MANUAL or getting a printed owners manual. This is a simple but very effective unit but you have to learn how to use it and "common sense" will not be enough!

Operation:
Tank with soapy solution is attached in place of the bag. It utilizes the air coming out of the exhaust to blow soapy water on a small screen that turns it into thick foam. The foam is simply laid over the carpet (you must vacuum before you shampoo). Foam allows to spread small amount of water over the larger area so carpet is not soaked all the way through. Foam is left on the carpet for a few minutes so it has just enough time to moisten the fibers of the carpet and loosen the dirt (not too long otherwise foam may dry). Then foam maker is set to "OFF" and you slowly pull Kirby vacuum over the area where you laid the foam. The rotating brush in the shampooer nozzle rubs the moisture off carpet fibers and and throws it into the tray in front of the unit. You will not see gallons of dirty water but that is because you did not put it on the rug in the first place. Carpet should dry within 1-4 hours (depends how many times you laid the foam and what is humidity in the room). After it dries it has to be vacuumed. Solution that did not get picked up with the shampooer brush dries and shampoo additives do not let the dirt stick back to the fibers of the carpet. It is loose when it dries but it is there so in order to pick up what is left loose you have to vacuum.
Shampoo:
You can use any carpet shampoo sold in your local store but make sure that this is carpet shampoo that makes foam and pay attention how much you have to dilute it with water as various shampoo products come in different concentration. Avoid using "just anything" that makes foam. Some household chemicals (such as dishwasher fluid) will do great job but it will leave carpet unprotected so dirt will stick to it so well that you will have a filthy rug in no time.

Disclaimer:
We are NOT affiliated with the equipment manufacturer in any way.

WARNING: This product can expose you to chemicals including Di (2-ethylhexyl) Phthalate (DEHP), which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov

Share your knowledge of this product with other customers... Be the first to write a review